Category: Industrial

Angled cable gland and PG threaded cable glands buyer guide? The areas of application of cableglandsonline.com EMC fittings range from machine and plant construction applications to telecommunications and airports up to use in hybrid vehicles – to name only a few. In the automotive sector, they are primarily used in hybrid and electric vehicles, but also in conventional vehicles to protect the sensor and on-board electronics systems from electromagnetic interference.

Cable glands perform a number of essential roles in cable management. Designed to attach and secure the end of an electric cable and the device it’s connected to, cable glands provide earthing, grounding, insulation, bonding and strain relief. They can also be used to seal cables which pass through bulkheads of gland plates.

Pg thread form of a German conduit pipe thread (DIN 40430) Unit: mm The screw thread referred to as a Pg 13.5 is a German DIN standard 40430 conduit pipe thread type. The thread angle is an 80 ° included angle and is similar to the JIS standard JIS C 8305 for thin steel conduit threads. Common applications for cable glands include aerospace, cleanroom, fire protection, industrial, marine, panel or enclosure, power or utility, railway, and telecommunications. Marine glands: Designed for application on ships, offshore mining and drilling settings, or other marine applications. See more info at PG Threaded Cable Gland.

CMP flameproof cable gland being suitable for armoured cables, provides mechanical cable retention and electrical continuity via armour wire termination. A detachable armour cone and CMP AnyWay universal clamping ring arrangement allows the cable to be easily disconnected from the equipment, for maintenance and change out etc, and re-connected with the same consummate ease.

What is a Barrier Gland? Barrier glands are similar to normal glands, except a compound sealant material is used to ensure the inside of the cable is gas tight as well as the outside. When Should a Barrier Gland be Used? BS EN60079-14 Electrical Apparatus for Explosive Gas Atmospheres Part 14 – Electrical Installations in Hazardous Areas (other than Mines) provides a selection process for deciding if a barrier gland is required. There are various options to consider, however if the hazardous gas require IIC apparatus, or if the volume of the enclosure is greater than 2 litres then it is likely you will need to use a barrier gland. IIC apparatus is generally associated with Hydrogen.

CableGlandsOnline.com offer a wide selection of cable glands and cable ties to fit your needs. All of our cable glands meet IP68 specifications as liquid tight and are resistant to low level acides and alkalis. These cable glands are also designed for install well. Here are you can find a full sizes of all kinds of cable glands. Whether your application requires metric, npt or pg or other applications. You will find what you need here. Source: here.

Concrete floor grinding best provider in Atlanta? At 360 Floor Cleaning Services, we go out of the way to make sure that your driveway looks spectacularly clean for days. And we do this by applying a high-quality concrete sealant. This sealant helps lock in the clean look and also hardens the concrete surface. Furthermore, it protects the surface from dirt and dust absorption, and stains. We use cutting-edge equipment and eco-friendly chemicals to pre-treat the oil stains and break it down and then pull up as much as we possibly can. We are a full service floor cleaning company, specializing in many areas of cleaning from industrial to commercial spaces. Get in touch with us today to learn how we can help you make your space cleaner than ever. We help you deep clean your facility to create and maintain a healthy and impressive work environment that promotes productivity and employee performance; and improves savings by decreasing labor cost, downtime, and operating expenses. We have the expertise and knowledge on how to use the latest cleaning equipment and technologies to deep clean and sanitize your property to complete satisfaction.

Looking for sanitizing services for public transportation services in Atlanta? We have a fabulous solution for you! And also a few cleaning advices … If you have kids in the house, it’s only a matter of time before candy ends up in the carpet. “Try to scrape it with a spotter brush or a butter knife,” Tarbox says. Then, using a sponge, apply water mixed with a mild soap. “It is important to get all of the sugar out of the area on the carpet,” he points out. “Failure to do so will result in that area attracting dirt and debris easily.” Once the candy is removed, dry the spot by blotting it with a cloth or towels.

Our team of experienced, licensed and professionally trained cleaning specialists will visit your facility well-equipped with industrial grade vacuum sweepers and eco-friendly products to remove dust, dirt, germs, and debris from the floor, and from areas that are hard to reach. We make sure that dirt and dust are completely removed from deep down so that your employees have a clean and healthy environment to work. Simply put, with us you don’t have to worry about dirt bothering your employees, their health, and performance. See a few more info on Warehouse floor scrubbing services.

Over-wetting occurs when too much water soaks into the bottom of the carpet. Some backing materials cause the carpet to discolor if they get too wet. Some carpets will shrink, literally tearing themselves up from the floor. If the backing and pad get wet, it is very difficult to dry them, and you run the additional risk of mold and mildew problems. The final carpet-cleaning hazard is stains caused by furniture coming into contact with wet carpeting. Many kinds of wood furniture will release some of the dyes in their stain if left in contact with a wet surface. Many pieces of furniture have feet that are at least partially metal. The metal can rust, leaving a stain in the carpet.

At 360 Floor Cleaning Services, we have a team of highly-skilled, experienced and professional cleaning specialists who can perform excellent warehouse floor cleaning to remove oil and grease. We can provide you with industrial grade and professional pressure washing services for floors, walls, and concrete to get rid of a variety of debris such as: Stains, Rust, Dirt, Grime, Mold & mildew, Food & drink stains and etc… Simply put, we can remove all types of dirt and debris, and ensure you have a floor that shines and sparkles, seamlessly.

Clean and Disinfect! Although the two may sound synonymous, they are very different. Cleaning, according to the Centers for Disease Control and Prevention, refers to removing germs, dirt and other impurities from surfaces. It does not kill germs, but reduces their numbers and thus the risk of spreading infection. Do this by wiping surfaces with soapy water or a cleaning spray and towel or paper towel. Find extra info on https://www.360floorcleaningservice.com/.

Non contact liquid level sensor online store from Drurylandetheatre? Liquid level controller refers to the control of high and low liquid levels through mechanical or electronic methods. It Can control solenoid valves, water pumps, etc. So as to achieve semi-automation or full automation. There are many methods, depending on the choice of different products. The float type liquid level controller is composed of a magnetic float, a measuring tube, a signal unit, an electronic unit, a junction box and installation parts. Generally, the specific gravity of the magnetic float is less than 0.5, which can float on the liquid surface and move up and down along the measuring tube. A measuring element is installed in the catheter. It can convert the measured liquid level signal into a resistance signal proportional to the change of liquid level under the action of external magnetism. And convert the electronic unit into 4-20ma or other standard signal output.

The advantages of ultrasonic liquid level gauge are very outstanding. It is mainly reflected in the following aspects : Safe and clean. The instrument has long service life. The measurement is stable and reliable with high precision. Of course, the ultrasonic liquid level gauge also has its own limitations and insurmountable defects. Specifically, it is mainly manifested in: There is a blind spot in the ultrasonic liquid level measurement. The dead zone is the area where the meter cannot measure. During the transmission of ultrasonic pulses, a small area near the ultrasonic transducer usually cannot receive sound waves. The blind zone where sound waves cannot be received is related to the measurement distance of ultrasonic waves. Generally speaking, the smaller the measurement distance, the smaller the blind zone. The larger the measurement distance, the larger the blind zone.

Ultrasonic Level Sensing measures liquid levels based on the principle of ultrasound. When ultrasonic waves encounter a high-density medium while propagating in a low-density medium, they cannot penetrate the high-density medium. There will be reflections at the interface of the two media. The ultrasonic liquid level gauge is made using this feature. Discover more info at Liquid Level Controller.

The External Ultrasonic Tank Level Sensor adopts the sonar echo ranging principle. It overcomes the influence of the tank wall on the transmission of ultrasonic signals. It adopts advanced digital signal processing technology. It can truly realize non-contact, high-precision measurement of the liquid level in the tank. The External Ultrasonic Tank Level Sensor can output 4-20mA standard signals or output the measurement results to the upper computer (or secondary meter) through the RS-485 interface. It can meet the automatic control of the system.

What does a level switch do? The function of the liquid level switch is to control the liquid level. For example, the water pump fills the pool with water, and the level switch can make the water in the water tank neither overflow nor empty, and there is always water. “ Can ultrasonic sensor detect water level? The ultrasonic sensor can of course measure the water level. When the ultrasonic level gauge is working, the high-frequency pulse sound wave is emitted by the transducer (probe), and is reflected on the surface of the measured object (water surface). The reflected echo is received by the same transducer (probe) and converted into an electrical signal . The time between pulse sending and receiving (the movement time of the sound wave) is proportional to the distance from the transducer to the surface of the object. See extra information at this website.

Pwht machine manufacturer from cmheat.com? Induction heating is the process of heating an electrically conducting object (usually a metal) by electromagnetic induction, through heat generated in the object by eddy currents. An induction heater consists of an electromagnet and an electronic oscillator that passes a high-frequency alternating current (AC) through the electromagnet. The rapidly alternating magnetic field penetrates the object, generating electric currents inside the conductor, called eddy currents.

Assembly is as simple as connecting the +terminal of your power supply to the +terminal of the ZVS driver and the -terminal of your power supply to the -terminal of the ZVS driver. The polarity of the working coil does not matter. I recommend an adjustable power supply and using a power meter to give you better control on your heat output. This induction heater works by pulsing the DC at a high frequency(about 160kHz). This creates a constantly changing magnetic field that induces eddy currents in conductive materials near the coil. Ferromagnetic materials will also heat up due to hysteresis. This is the heat produced from rapidly changing magnetic fields in the material. Induction heating is more efficient than many other methods because there is less wasted heat. For example, induction cooktops are more efficient than electric and gas stoves. I’ll be making more attachments and demonstrating more practical uses for inductive heat.

MYF Melting Furnace is designed for Non-ferrous Metal Melting. Which is used for Copper, Aluminum, Zinc, Tin and Lead melting. The power size is 40KW-600KW. The Induction Heating Power and Melting Furnace are equipped with water cooling system. The air cooling ones will need customization.The Graphite Crucible furnace capacity is 100-1000kg copper or equivalent. The induction melting system consists induction heating power, melting furnace and graphite crucible.We can choose the right electric power and melting capacity upon the melting speed requirement. The standard heating power size and Crucible capacity is as following. Read more info at induction heating equipment manufacturers.

The use of my wire choice is quite important here. I used what is known as Litz wire. Litz wire consists of many individually insulated wires. It is the preferred wire for use in high frequency application due to the skin effect. The skin effect is the tendency of current to flow on the outside of a conductor at high frequencies. The higher the frequency, the shallower the skin depth will be. Using Litz wire will result in much more efficient working coils for your system. Not only does it transfer the energy more efficiently, it also generates less heat of its own. If you have 10amps flowing through 260 strand Litz wire, that’s only 38mA of current in each wire. 10amps through a single conductor will generate substantial heat depending on the size. If you do not want to use Litz wire, the next best thing is copper tubing. It has more surface area for the current to flow so it is more efficient than an equivalently sized solid core wire.

MYF Melting Furnace is designed for Non-ferrous Metal Melting. Which is used for Copper, Aluminum, Zinc, Tin and Lead melting. The power size is 40KW-600KW. The Induction Heating Power and Melting Furnace are equipped with water cooling system. The air cooling ones will need customization.The Graphite Crucible furnace capacity is 100-1000kg copper or equivalent. In general, it will cost 300-350KW*H electric power to melt 1MT copper. Read more info at https://www.cmheat.com/.

Best solar panel manufacturer? So just what is the best generator for home use? It depends on your situation. For example, the best standby generator for home use isn’t necessarily the same as the best generator for running your off grid home. And the best generator for an off grid cabin depends on the length and frequency of the run times. It also depends on whether your off grid cabin has any other energy source (ie. solar panels or a windmill.) And how much power your home systems require. When you’re reading the specs on a generator, look for any manufacturer’s recommendations on whether it’s for occasional use, emergency use, or to use off the grid. Not all generators are made to withstand the heavy use of an off grid home. So don’t make the off grid homeowner mistake of choosing one labeled “emergency use” as your everyday power backup for solar panels in the low-sunlight days of winter. Doing so could void the manufacturer’s warranty.

Since you will be meeting some of your energy needs with the electricity your solar system has generated, your energy bills will drop. How much you save on your bill will be dependent on the size of the solar system and your electricity or heat usage. Moreover, not only will you be saving on the electricity bill, but if you generate more electricity than you use, the surplus will be exported back to the grid and you will receive bonus payments for that amount (considering that your solar panel system is connected to the grid). Savings can further grow if you sell excess electricity at high rates during the day and then buy electricity from the grid during the evening when the rates are lower.

CETCSolar Bifacial solar panel is produced with solar cells, 2.5mm tempered glass, split design junction box and other parts. CETCS Solar panels have acquired TUV, CE, SGS, INMETRO certifications. Bifacial solar panel can got more energy generation. The power generation gain of the Bifacial Solar Panel mainly comes from the back side, and by receiving the reflected light from the atmosphere and the reflected light on the ground, the overall power generation of the bifacial module is increased. When the sun shines on the Bifacial Solar Panel, some of the light is reflected by the surrounding environment to the back of the panel. This part of the power can be absorbed by the battery, improving panels efficiency. Discover additional info at solar panels.

Those appliances in the household with the highest electricity demand are the dish washer, the washing machine, the tumble dryer and the kitchen stove. These can easily be equipped with timer switches, so that they run during the day, when the solar generator on the roof is producing a lot of output, which can be used directly. A high-wattage stove might be a challenge for PV by itself. In this case, a large storage unit (solar battery) can be used as a buffer for short-term load peaks. Because it is not just the number of kilowatt hours on the roof that has to be sufficient, but also the currents made available at short notice. This determines if a storage unit is designed for capacity (in kilowatt hours) or output (in kilowatts).

Those appliances in the household with the highest electricity demand are the dish washer, the washing machine, the tumble dryer and the kitchen stove. These can easily be equipped with timer switches, so that they run during the day, when the solar generator on the roof is producing a lot of output, which can be used directly. A high-wattage stove might be a challenge for PV by itself. In this case, a large storage unit (solar battery) can be used as a buffer for short-term load peaks. Because it is not just the number of kilowatt hours on the roof that has to be sufficient, but also the currents made available at short notice. This determines if a storage unit is designed for capacity (in kilowatt hours) or output (in kilowatts).

Solar Products have acquired TUV, CE, SGS, CQC and INMETRO cetrificate. We have passed the international quality system certification: ISO9001, ISO14001 and ISO17025. We also have the professional qualification of building electrical and mechanical installation engineering, specializing in the design, construction and operation and maintenance of distributed solar power plants, with professional system design capabilities. Read more info at https://www.cetcsolarpv.com/.

MIG welding machines and a few welding guides? The Autojack MIG100 has its flaws but none of them make a convincing enough case to prevent the model’s appearance on our list. It’s a good product for a lot of different reasons. First, it incorporates 4 stage power settings. Add to that the variable wire speed control and you have yourself a truly versatile tool. The internal turbo fan cooling system here is represented by an oversized blower that circulates air at a higher speed. The air vents on the sides of the model are also larger than average, a design solution that improves heat dissipation. Having said that, what we like most about this MIG welder is probably just how suitable it is for people with different levels of expertise, from beginners and hobbyists to experienced welders and professionals.

How to pick a welder tips: MIG wire inch button: A great feature. This will save you wasting your shielding gas when feeding wire through at the start of a new reel. Gas purge button: Another nice option. Save yourself some MIG wire, when you’re setting your gas flow. Burn back facility: Not all machines have this externally, buy it’s good to be able to trim the burn back to the wire according to the application & operator. Selecting the correct amperage machine: Generally, you should work on 35-40 amps per 1 mm diameter of material to be welded. Read extra details on Welding supplies Ireland.

Eliminate Any Extra Welds from the Design: Look for ways to modify product designs to eliminate unnecessary welds. For example, one company that manufactured boxes originally had a design that called for welded lift handles on each side of the box. By simply changing the design of the box to cut out lifting slots, it eliminated the need for welding the handles – saving time and money. In another instance, rather than making a part with an open corner, the design was changed to accommodate a closed corner, which meant 1/3 less metal required to fill the corner. Look for Items That Can Be Welded Rather Than Cast: We’ve already discussed ways to eliminate welds to create efficiencies, but what about adding welds? In some cases, it may be more cost effective to weld metal pieces to a part rather than cast the entire component in a costly alloy or exotic metal. For example, a company that originally used a part cast in a high-nickel alloy found that 50 percent of the part could be composed of standard, structural steel which allowed a savings in material and thus a savings in total cost. Also, the company was further able to redesign the part so that it was more efficient.

A few advices about welding equipment, MIG and TIG welders, plasma cutters. MIG Welding Increases Welding Speed: In addition to welding aluminum and other softer metals, MIG-welding works faster, provides cleaner welds, and handles many different types of metals. The downside is its complexity. MIG Welders need direct currents, a steady stream of inert gas, and precise control of their torches. The amount of heat generated from MIG welding provides the deep penetration required for a strong weld, while also melting the feed wire rapidly enough to maintain a higher welding speed than other techniques. Given the inert gas required for MIG welding, keep in mind that this technique cannot be conducted in windy areas. The Right Stick Electrode Increases Welding Speed: There are three kinds of electrodes used for stick welding: fast-fill, fill-freeze, and fast-follow. While each electrode has its advantages, the fast-fill electrodes melt quickly and allow welders to work faster. Find additional info on https://www.weldingsuppliesdirect.ie/.

USA market pick: At just $99, the Goplus is a fantastic value considering what it is equipped to do. In fact, it is the most affordable welder on our list, beating out its competitors by hundreds or even thousands of dollars and putting it in a class of its own. For a budding hobbyist not yet sure if welding is for them, you can’t go wrong with the Goplus. After all, for $99 its welding thickness and the duty cycle is about what one would expect (don’t look to buy this welder if you want it for heavy duty use). The Goplus is light and compact when compared to most other welders. Flux core wire is included. It has four levels of easily adjustable current flow and ten levels of wire speed. The Goplus is able to weld steel and iron at below ¼ inches thickness.

The Hobart Handler 140 is an excellent choice for beginner welders, which is why it’s probably the most popular welder on the market. This thing is solidly built and is a step above many of the other 140A welders. The arc runs smooth and produces great results. It’s suitable for a range of general repair tasks and projects like trailer frames, autobody repair and anything up to 1/4 inch thick. If you’re just getting into welding, you can’t go wrong with this little machine! What’s better is that it’s an absolute steal at under $500. See the full review here.

Best tin cans manufacturer? The wine tin boxes series has become a hot product of Nice-Can. Nice-Can has great production capability and excellent technology. We also have comprehensive production and quality inspection equipment. Wine tin boxes have fine workmanship, high quality, reasonable price, good appearance, and great practicality. All of them are well-trained. Nice-Can insists on the service concept that we put customers first. We are committed to providing one-stop services.

Top ten cattle business roadshow winner: Ms.Joanna, chairman of Guangzhou Nice-Can Manufacturing Co., Ltd, took the 7th place to share. “Nice-Can has been a foreign trade market since the beginning and has never contacted the domestic market.” Ms.Joanna shared his passion and talked about how his enterprise entered the domestic market step by step from the beginning, and shared the whole Internet operation situation and the transformation of the enterprise from the traditional operation thinking to the Internet operation thinking for everyone at a fast pace. The network marketing started slowly from 0 and grew slowly, which caused the long applause on the spot.

Nice-Can is a professional manufacturer specalised in researching, developing and manufacturing tin boxes and tin cans for 20 years. Serving for 63 countries and regions around the world. We provide one-stop service of design + R&D + mold + proofing + production + door-to-door. See extra info at promotional tin.

Nowadays, many product markets are very competitive, and how to make their brands in the forefront of the industry, businesses are constantly changing marketing methods to cater to the rapidly changing consumer concepts of people. With the traditional carton and plastic packaging beginning to be eliminated, tinplate boxes are ushering in a heating up, and there are more and more tin box processing factories.

Tea cans, moon cake boxes, cosmetic boxes and cookie boxes have been packed in tin boxes for a long time, and the quality of the products has been greatly improved after they are replaced with tin boxes. Fine products are more popular. In order to comply with market development and people’s consumption psychology, tin box packaging has also appeared more and more widely, and many businesses have designed customized tin box packaging for their products and consumer groups, hoping to make their products more consumer Attractive.

Nice-can is a professional tin boxes manufacturer with 20 years experience of research,development and production about tin boxes and tin cans, for 63 countries and regions around the world, to provide design + R&D + mold + proofing + production + door-to-door one-stop service. See extra info on https://www.nice-can.com/.

Automated Feather Duster: Using Encore engineered and designed standard machines and robot mounted assemblies Encore offers an extensive assortment of custom feather duster systems for a wide variety of vehicle and product sizes. Current systems range from full robotic feather dusters with optional integrated hoods to floor mounted hood assemblies. Encore standard single column articulating machines can be provided in clean wall or in booth design with servo controlled articulating axis or manual adjusted fixed machines. A combination of both robotic and fixed machine feather dusting systems can offer the most flexible design for complex requirements. Encore also offers a unique hoodless truck box interior robotic feather duster. Removing the hood allows the feather rolls to get into areas which would be inhibited by the presence of a hood. Instead a fixed hood is mounted alongside the robot allowing the rolls to be cleaned between boxes. Encore also manufactures in house all the Ostrich feather rolls for the Encore systems as well as any replacement feather rolls for existing feather duster systems.

TKS Industrial has acquired Encore Automation, a leader in Automation and Robot Integration in the Automotive and Aerospace industries. We design our robot paint systems to provide the most efficient painting process within a spec’d time frame to determine the optimal number of required robots. TKS employs a large staff of full-time engineers. From sizing equipment based on heat loads and specifications to designing new layouts for brand new paint shops, our Engineering & CAD team can provide full-service engineering. We design custom paint booths, industrial ovens, and other paint process equipment.

TKS offers a proprietary high-pressure water spray technology to clean car bodies of weld balls and iron dust prior to the film build processes. A clean car body is critical to a quality surface finish. TKS offers design, fabrication, and installation of industrial tanks for electro-coat and UF rinses. Our unique lineup includes the iron removal system (Flood Spray), high-performance washing system (Parallel Separator), and counter-flow circulation tank in the degrease process, and high-pressure spray water washing processes. I-LAS (Impact Blast Washer System) is our high-performance water washing system which efficiently remove iron powder from body surfaces with minimal water and pressure. Find even more info at automobile spray booth.

TKS can design heated flash off tunnels for your paint process, using a heater box to provide hot air blow (HAB) to allow for the waterborne paint to set prior to the next coat of paint. Typically followed by a short cooling tunnel with cold air blow (CAB) to return the vehicle to near room temperature before the next layer of paint is applied.

All four major ovens: E-coat oven, Sealer oven, (optional) Primer oven, and Topcoat oven all consist of heat-up and hold zones. In a 3-wet paint booth process arrangement, there isn’t a Primer oven, instead a heated flash off (HFO) is used. Sometimes there are also smaller ovens for black-out and cavity wax. We offer a paint-drying oven that responds to temperature increases in body areas. The oven design will increase heating in zones of thick parts, such as sill inners or pillars where it is difficult to dry paints, while maintaining the temperature of keep-zones with a minimized flow rate to reduce dirt contamination and reduce energy usage.

TKS is committed to providing our Customers with products and services that meet or exceed expectations. We will identify and anticipate the Customers’ current and future needs and create and implement quality products to satisfy those needs. Through this, we aim to maintain an impeccable reputation in our field and ensure our success well into the future. Read additional information on this website.

Top China products directory? Beijing holds its industrial power due to its sister city, Tianjin, which itself is another manufacturing giant. This city is a leader in aerospace and aviation, mobile phones, automobiles, and alternative energy products.

China is the fourth largest oil producer in the world with the country having a production of 1.3 billion barrels in 2002. The size of oil deposits in China is not known for numerous oil exploration studies being conducted in the country. Despite China’s enormous oil production, the country is still oil-deficient and being the world’s largest oil consumer in the world, and the country relies on oil imports to meet its domestic oil demand. China has also invested in renewable energy which is seen as the new frontier in the energy industry, with the country being the top electricity producer from renewable sources. The country has numerous wind farms located in its vast territory as well as in offshore sites to harness wind energy which according to researchers from Tsinghua University, can meet the country’s electricity needs. In 2013, the total electricity output from wind sources amounted to 140 Tw-h.

Biggest companies in China ? PetroChina is an oil and gas operation headquartered in Beijing. Founded in 1999, the company has specialised in the exploration, development, production and sale of crude oil and natural gas. PetroChina has sales of $322.8bn and a value of $198.7bn. In its first quarterly report for 2019, PetroChina highlighted that the company and its subsidiaries’ output of crude oil saw a 4.6% increase year-on-year to 223.4mn barrels. It is the second largest oil producer in China, with over 494,297 employees.

Longkou Runjie Machinery Co., Ltd, also known as Runjie Machinery, is a manufacturer of EPS machines and different shape molding machines for over 18 years. Our advantage is that we not only make the machines but also specialized in making the products. We have rich experience in both machinery and production, and we know customers’desires. Our machines are mainly used for packing and construction purposes. Most of our products are green and environment-friendly, some of our customers using our machines even gained national rewards for their products. We have a team of professional engineers who engage in machine developing, manufacturing and installation so that we can give our customers services from factory layout design to machine installation as well as after-sale service. As we make products, we can find out the machine problems and then improve it at any time. Therefore, our machines always work stably and have few problems. We also offer the best after-sale service. Whenever the customers have any problems, we can support them online, or if necessary, to send engineers to go to the customer’s place. Besides, whenever we have new techniques, we will inform our customers for them to upgrade their products. During the last 10 years, our machines have been exported to many countries around the world and received customers’ praise worldwide. See additional details on Runjie eps cutting machine.

Jinko Solar is a solar panel manufacturer headquartered in Shanghai. Founded in 2006, the company started out as a wafer manufacturer and went public on the New York Stock Exchange in 2010. They distribute their solar products and sell its solutions and services to a diversified international utility, commercial, and residential base in China, the United States, Germany, and many more. By the end of 2018, Jinko Solar shipped 9.7 GW of silicon wafers, 7.0 GW of solar cells, and 10.8 GW of solar modules. As a result, the company is considered as the current largest solar panel manufacturer in the world.

JHX brushes is an ISO 9001 certified manufacturer of standard & specialty brushes for the commercial, aerospace, military, medical & electronics industries. No other company offers such a wide range of high quality and best price industrial brushes to meet your most demanding requirements. We provide quality products at competitive prices with same day delivery on thousands of items. Discover more info at https://china-select.com/.